Skip to Content
Technical Articles
Author's profile photo RAJA SEKHARA REDDY BANNURU

Adding the Shifts to the Resource/Work Center in the Capacities Tab

Hi All,

The purpose of this document is to explain how to add the Shifts to the Resource/Work Center Capacities tab,

Prerequisites : Set up the Grouping Key at the Configuration, with the required, Shift Breaks, Shifts Definitions & the Shift sequences, as per the Business requirement.
Follow the below link, for setting up the same. https://wiki.scn.sap.com/wiki/display/ERPMan/How+to+maintain+shifts+for+work+center

Steps to be followed for adding the Shifts, in the Capacities Tab of the Resource/Work Center.
T Code: CRC2 >>>>Go to the Capacity Header Tab

In the next screen that is displayed, Enter the Values for the fields marked 1,2,3
Click on Intervals & Shifts Icon

In the next screen, that displayed,
Click on + Intervals, Button

In the next screen that is displayed
Enter, Valid from & valid to Values, as shown below & Press Enter

In the next screen that is displayed

Keep the Cursor on the Weekday (Ex : MO) & Assign the Last Shift ( Ex : YQS3)

Assign YQS3 & Press Enter

In the Next Screen that is displayed
Keep the Cursor on the Weekday (Ex : MO) & Click on + Shift ( Icon, on the Top)

In the Next Screen, that is displayed

Enter the Additional Shift YQS2 (Above YQS3 Line).

In the Next screen, that is displayed, Keep the Cursor, on the Weekday (MO) & Click on + Shift Icon, to add the new Shift YQS1

In the Next Screen that is played, Enter/Assign    YQS1 & Press Enter

Once maintained, you will get the details, like shown below

Follow the same for the remaining Weekdays, by following the sequence, first YQS3, then YQS2, then YQS1

Save the Data >>> This completes the Shifts addition, to the Capacity Tab
Now Check the Available Capacity using the T Code : CM01

*****
Please share your comments/inputs/feedback to make this document as the  Most Useful & User-Friendly one.
Thanks & Regards : Raja Sekhara Reddy Bannnuru

 

Assigned Tags

      8 Comments
      You must be Logged on to comment or reply to a post.
      Author's profile photo shailesh mishra
      shailesh mishra

      Well done Raja. Quite elaborative! Thanks

      best regards

      Shailesh Mishra

      Author's profile photo RAJA SEKHARA REDDY BANNURU
      RAJA SEKHARA REDDY BANNURU
      Blog Post Author

      Many Thanks Shaliesh,  for your Kind & Encouraging comments

      Best Regards : Raja

      Author's profile photo Vignesh Veerasamy
      Vignesh Veerasamy

      Hi RAJA SEKHARA REDDY BANNURU

      Informative document.Keep going.

      Vignesh V

      Author's profile photo RAJA SEKHARA REDDY BANNURU
      RAJA SEKHARA REDDY BANNURU
      Blog Post Author

      Many Thanks Vignesh for the kind feedback.
      Best Regards : Raja

      Author's profile photo Vignesh Veerasamy
      Vignesh Veerasamy

      RAJA SEKHARA REDDY BANNURU  would like get insights on below

      1.How capacity planning is impacting MRP ? in S4 I am not able to see the graph output in form of Gantt Charts.

      2.Can two plants with same work centre [ex : WC1 for plant1 & WC1 for plant2] nomenclature handled in capacity planning?

      Thank you.

      Vignesh.V

      Author's profile photo Ramkumar RV
      Ramkumar RV

      Thanks for sharing nice document.

      Very detailed explanation.

      Thanks

      Ramkumar RV

      Author's profile photo RAJA SEKHARA REDDY BANNURU
      RAJA SEKHARA REDDY BANNURU
      Blog Post Author

      Hi Ram,

      Many Thanks for your kind feedback.
      Best Regards : Raja

      Author's profile photo Anthony Dellarte
      Anthony Dellarte

      Great read!  I have a question.  Due to the strict management of higher tier transactions, many of us at our organization do not have OP4A, therefore I could not use grouping for shift definitions. The shifts where created by going into the work center and simply inserting an interval with shifts.

      Any concerns with setting up intervals/shifts without using grouping for shift definitions?