Skip to Content
http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/webcontent/uuid/925b02f9-0b01-0010-bbbf-c68268bb3c41″ width=”235″/> http://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/docs/webcontent/uuid/7ec202f9-0b01-0010-589e-a51bcd596fed” width=”235″/>

1. Configuring the NetWeaver system.

a. Log into the SAP system. b. Go into SE38 for the Preparation Check procedure. c. In the program field = RTCCTOOL d. Then hit Execute button. The following screen will be shown: image Depending on your current location you should need to select the corresponding nearest SAPSERV system, then leave the defaults values and click (image) button. The following screen should appear: image You will need to check every Red status item and read the associated OSS note to correct the issue first. e. Then hit Addons&Upgr button. image f. Execute Procedure after add-on implementation button, only in case of the Red cross. The following screen should appear next: image Depending on your current version, the comment information shown above could be different. g. Hit the (image) check. The next screen should only have green checks now: image

2. Configuring transaction SDCCN.

a. Call transaction SDCCN. b. Choose from the menu Utilities –> Activate image c. Confirm with Yes. image d. Confirm with Yes. image e. Confirm with Yes. image f. Confirm with (image). image g. Confirm with (image). image h. Confirm with (image). Now, the following screen should appear: image Click Back button. image

3. Configuring connection to Solution Manager.

a. From the menu select Go To –> Settings –> Task-specific. The following screen should appear: image b. Highlight RFC Destinations –> Settings. c. Click on the square/table next to Settings. image d. Switch to Change mode. e. Click Add RFC Destination button. f. Enter a description like My Solution Manager Destination. image g. Open the matchcode or press F4 in Destination field. h. Choose your Solution Manager RFC destination. Note: This destination should already exist or must be configured manually through transaction SM59. image Example: image i. Hit (image) check. image j. Select the Solution Manager destination recently created. k. Click Set Master SAP Solution Manager System button. l. Check Destination field and select Solution_Manager from the matchcode. image m. Hit (image) check twice. image n. Confirm with Yes. image o. Hit Back. p. Hit Refresh button. image

4. Starting first Service Preparation Check.

a. Highlight Service Preparation check. Then Edit –> start now. image b. Confirm with Yes. image c. Confirm with Yes. image d. Confirm with Back button. image e. Confirm with Yes. The following screen will be shown: image Congratulation, you have successfully activated the new SDCC transaction and configured the EWA connection to your Solution Manager system.

Related Solution Manager configuration guides on SDN

System Monitoring configuration guide for Dummies

Service Desk configuration guide for dummies.

CCMS Rule Based Monitors configuration guide for Dummies

To report this post you need to login first.

6 Comments

You must be Logged on to comment or reply to a post.

  1. Raj Sam
    Thanks for your series of Blogs on Sol Manager / SDCC/ CCMS… its so wonderful..all would be helpful for setting up Sol manager.. Appreciate your initiative..

    Thanks,
    Raj

    (0) 
  2. Anonymous
    In absence of SAP guides for configuring scenarios step by step, your blogs are a real help. Keep up the good work.

    warm regards,
    Shantanu Bansal
    SAP Netweaver Consultant

    (0) 
  3. Gajanand Gupta
    Its a very good blog and i have done my config using this and i dont find any single step other then this. this helps me gr8. Some times due to support person who dont have knowledge about the new technology then the customer does not get the latest things and they get a wrong picture in their minds about the product.

    Thanks
    Gajanand Gupta

    (0) 

Leave a Reply